How to install a frame for a license plate video

How to remove the number frame?

A license plate confirming state registration is an important attribute of any car.
Appearing on the roads without license plates is fraught with serious consequences for the car owner (from a large fine to deprivation of rights for 3 months). Therefore, he must take care to prevent such unpleasant situations. Today, for attaching license plates, license plates are used, special structures made of metal or high-strength plastic that do not lose their mechanical properties over a wide temperature range.

Number frames from car dealers

When purchasing a car at a dealership, drivers rarely pay attention to the license plate.
Car dealers use this to their advantage. Most often, advertising for a car manufacturer or a separate car dealership is placed on the device. Such inscriptions do not disturb the driver too much, especially since the device can be changed quite quickly. This is a free and effective advertising campaign for car dealerships. The fasteners work fully, so many drivers prefer not to waste time on replacement.

Functions of number frames

The functionality of the number frames is as follows:

In addition, car dealers use license plate frames as advertising platforms for their own services; for this purpose, they make custom car frames with their own logos and contact information. That is why the production of frames for license plates and installation on cars is in increasing demand.

How to remove the number frame?

Situations often arise when it is necessary to remove the license plate, and often the frame holding it, this can happen, for example, in the case of:

If you do not take into account anti-vandal frames, the dismantling of which is best left to specialists, then to remove ordinary license plate frames, you need to get to the fasteners that secure them to the body or bumper. To do this, first of all, you need to remove the license plate. It is at this point that most motorists encounter difficulties, since the license plate is attached using special latches. At this step, the burning question appears: “How to remove the number frame?”

Types of devices

Frames for car license plates feature a wide range of additional functionality:

1. Standard plastic frame.
2. Anti-vandal ones are made of aluminum. They serve as protection against dogs and intruders.
3. Frame with mesh.
4. Equipped with backlight or rear view camera.
5. Folding.

There are mounts that allow the driver to hide the license plate when entering the coverage area of ​​road cameras.

These include:

• curtain frames;
• changelings;
• with a slope.

Such devices are installed so that the car number cannot be remembered or photographed. After the driver presses the appropriate button, the changer changes the license plate to another. The tilted frames lower the license plate to a position from which it is impossible to see the numbers; the curtains cover the license plate.

The use of fasteners that cover the license plate is prohibited by law, but despite this they continue to be in demand among car owners.

How to open the number frame?

A manufacturer that produces car accessories usually adheres to certain standards, because license plate frames must take into account the standard dimensions of the license plates themselves and match the design of the car body (bumper). However, with regard to design features, the flight of design imagination is less limited. Therefore, the method of fixing the sign on license plate frames from different manufacturers may differ significantly. The main obstacle to opening the number frame is a lack of understanding of its design and the location of the locking latches.

Of course, if the frame was installed by the car owner himself, he can remember the assembly sequence and try to open it in the reverse order, following the instructions. The easiest way to remove the frame is when the car frame is damaged and requires replacement with a new one. Considering that the retail price of a new accessory is from 120 to 200 rubles, the thought of repairing it is unlikely to occur to anyone. In this case, you can remove the license plate by simply breaking the structure completely.

To open the number frame carefully and without damage, you need to carefully familiarize yourself with its design, installation instructions (manufacturers usually post them on their websites), arm yourself with a thin knife that will allow you to determine the location of the latches and a slotted screwdriver that will help unfasten the latches. Be patient, and, of course, rely on your own intuition.

And it is quite likely that everything will work out. If you have frames manufactured by AEP, installation instructions can be found on the manufacturer's website.

Source

How to attach number frames

The following fixation mechanisms exist:

• One-piece. In this case, the number is held in place by several fasteners, and the frame itself is monolithic and firmly adheres to the car body. This type of mechanism is the cheapest, however, it has several disadvantages. Firstly, during installation the frame may become deformed. Secondly, it is difficult to remove it not only for intruders, but also for the owner of the car. Also, this simple mechanism will not allow the installation of additional protective elements, for example, a curtain or anti-vandal fasteners.
• Two-piece with latch. Such frames are most popular due to their high level of protection and relatively low price. Unlike one-piece models, curtains and other anti-vandal devices can be installed on this number frame. Two-part products consist of a base and a front cover, so the accessory can only be opened in a specialized workshop. Often such products are called cassette. They are made from both stainless steel and plastic.

Find out how to remove license plates from a car

Typically, license plates are installed by a dealer or a specialist at a car service center. Therefore, when selling a car, restoring or painting bumpers, some drivers are faced with the question of how to remove license plates from a car without damaging anything.

The procedure can be done independently, and in rare cases it takes a long time.

User tips

How to attach a license plate to a car in a frame? Let's turn to user recommendations. Before starting work on installing a license plate, experienced motorists recommend placing small washers under the bolts on the front side in the places where the rear flap is attached to the bumper itself. This will ensure that the car frames are held firmly in place.

For fastening, you can use plastic harnesses. These fasteners will ensure secure fixation of the frame in the holes.

Such a mount can always be found on sale and is easy to secure the numbers in the frame as needed. Wire cutters are used to remove excess fasteners.

How to assign a rear number? This can be done in a similar way. This mount is quite strong, but not very aesthetically pleasing in appearance. Therefore, you can use the second method.

For the second method, you must first purchase plastic pistons for attaching the rear door. They are a plastic Christmas tree shaped rod with a plastic cap on top. The excess part of the fastening will also need to be cut off.

The plug is inserted into the number and tightened with a screwdriver. This fastening also has a high level of strength. At the same time, the aesthetic appearance of the license plate does not suffer. Everything is neat, durable and practical. The license plate will not come off at the attachment points.

If there is a frame

The frame itself is made of plastic. The license plate in the frame at the top and at the ends is pressed with hooks that hold it in a given position. At the bottom there is a wide strip that is removed before removing the license plates from the car.

Frames for license plates are available in several versions, which differ in the way the lower removable strip is attached.

Option 1

The strip is attached from the back to one latch along its entire length.
To remove it, just bend the frame with the number slightly towards you and use your fingers to pry the strip from behind towards the bumper. The latch comes unfastened and the strip is removed. The number is carefully removed from the fixing hooks using a top-down motion. To simplify the task, use a flat-head screwdriver.

Option 2

The bottom strip is first inserted into the end grooves, then fixed in the middle with two latches.

Dismantling the strip proceeds in the reverse order:

The number is removed from the frame, as in the first option.

Option 3

In this design, there are 2 locks securing it on the bottom strip. The sign is tightly inserted into the grooves located at the top and bottom along the entire length of the frame.

To remove a number, the locks on the bottom of the frame are opened towards the center.

The bar is lowered, removing the lower part of the sign from the groove. To release the upper part, just insert a screwdriver into the holes on the number, rest it against the plastic of the frame and lower it down. The number has been removed.

If there is no frame

Car owners who are not satisfied with the frames attach the numbers to the bumper with screws or rivets.
In the first case, to remove the sign it is enough to use a screwdriver. If the screw has become stuck and will not come off, it is better to immediately treat it with WD-40, wait 5 minutes and try again.

Rivets and self-tapping screws with licked heads are carefully drilled out. It is not recommended to use a grinder, as there is a high probability of damaging the surface of the sign during work.

Drilling is carried out while protecting your eyes with goggles.

Possible problems and nuances

Sometimes the old frame cannot be disassembled. In this case, its end is heated with a hairdryer until softened and bent, the number is removed.

When selling a car, if there is no desire to keep the existing number, it is torn off without unnecessary ceremony. The main thing is that the symbols printed on it are visible.

Issues relating to motorists' rights are often more important than they appear at first glance. A driver may lose his license or suffer other severe penalties due to ignorance or misinterpretation of laws and regulations. Do not be lazy to dive deeply into the essence of the issue being studied, do not hesitate to ask advice from professionals.

Source

How to save car license plates through State Services step by step

The Government Services portal was created to simplify the interaction of government departments with ordinary citizens. Actually, this electronic resource does not independently provide the necessary services, but acts as an intermediary, redirecting requests to the right authority. With the help of State Services, car owners were able to submit applications to the State Traffic Inspectorate.

Among other things, vehicle owners can submit applications to the traffic police with a request to retain the license plate number when selling the car. The reasons for this vary: some are accustomed to the old numbers and do not want to part with them. Other citizens are the owners of “beautiful” signs and do not want to transfer them along with the car they are selling. To keep your old license plates, you will need to submit a corresponding application to the traffic police. The easiest way to submit it is through the State Services portal.

Authorization on the site

Only users who have passed the authorization procedure can access the services provided by the site. Step by step it looks like this:

1. We go to the State Services website by following the electronic link.
2. On the portal’s home page, the system will prompt you to either log in by entering your password and login, or register. Since we do not yet have our own personal account, we select the “ Registration ” button.
3. Then you need to fill out the proposed electronic questionnaire, entering the information requested by the system in the appropriate fields.
4. After this, a confirmation code is sent to the specified phone number or email. The lifespan of the code is three days. During this time, you need to have time to enter it on the website by registering your personal account in “State Services”.
5. The last step is to come up with a unique password and login, which will then be used to log into the site.

The list of services available to the user depends on the authorization level. In total, “State Services” provides for four of them: one for organizations, and three more for individuals. The first, simplified level, makes it possible to obtain reference information and pay some fines through the website. For simplified authorization, you need to enter your full name, contact phone number or email. Users who have a personal account of the second, standard, level can request various certificates from government agencies through the portal, submit complaints and suggestions online.

The highest level of authorization on State Services is confirmed .

To receive it, you will have to personally visit the district office of the MFC, presenting your passport as a citizen of the Russian Federation and your SNILS pension card. After checking the provided documentation, MFC employees will issue an envelope with a unique code. After maintaining it on the website, your personal account is upgraded to a confirmed level.

Now the user will be able, among other services, to submit applications for the production of official documents and their replacement. To save numbers through Gosuslugi, you need to have a confirmed profile, since the system in this case operates on the passport data of the car owner.

Selecting the required service

After completing the authorization procedure, go to your personal account “Gosusulg”. The site does not directly provide such a service as saving license plates, so there is no point in looking for such a section in the menu. However, it is possible to submit such an application through the website.

Let's consider the entire process of choosing the service we need step by step:

1. On the main page of the site, select the “ Services ” section.
2. In the list that opens, we find the subsection “ Transport and driving ”, and then, on a new page, select “ Vehicle registration ”.
3. In this tab you should select .

4. The next step is to go to the subsection “Change of registration data in connection with the transfer of ownership (purchase and sale)" On a new page, the system will provide information regarding the time allowed for the provision of the service and the amount of the state duty.
   Read also:  “Beltechosmotr” suggests canceling the first aid kit and fire extinguisher when undergoing maintenance
5. After reading the information, click the “ Receive a service ” button on the right side of the screen, and the system will take you to the page with the application form to the traffic police.

Filling out and submitting an application for vehicle registration

Filling out an application to the State Traffic Inspectorate is carried out in several stages. In the first section of the electronic form, information about the type of vehicle and the form of ownership in which it is located is entered. For example, in the “ Vehicle ” item, select “ Car ”, and in the “ You are ” item, check the box next to “ Owner ”.

Next is a section with personal information about the user - full name, age, gender, TIN, e-mail, telephone. There is no need to fill out these sections, since the system will automatically enter information from the profile created during authorization. In point No. 6, when the system asks if you need to obtain a state sign, oh, and enter the data of the number that you would like to keep for yourself. After this, information about the vehicle is filled in: type, body number and VIN.

When all the required information about the owner and the car is entered in the appropriate columns, select the traffic police department where you would like to re-register license plates. Previously, this was only allowed at the traffic police departments at the place where the car was registered. But, with the introduction of a unified electronic database, the owner has the right to perform legally significant actions with his car in any traffic police department throughout the Federation. On the website, select the department that suits you and make an appointment, indicating a specific time and date.

We write a separate application for saving numbers, sample

To save license plates, the owner must write a corresponding application and submit it to the registration department of the traffic police. A sample application is presented below:

Contact the traffic police

After making an appointment through Gosuslugi, the owner of the car being sold comes at the appointed hour to the traffic police department of his choice. Here he presents the following documentation:

• Your general passport.
• Vehicle registration certificate.
• Certificate of state registration.
• A valid MTPL policy.

License plates are deposited with State Traffic Inspectorate employees until the citizen purchases a new car. Today the maximum shelf life is 1 year . The procedure for re-registration of numbers is paid.

The amount of the collected state duty consists of several parts:

1. Production of new numbers, with the same data – 2,000 rubles.
2. Changes to PTS – 350 rubles.
3. New STS – 500 rub.

When paying the state fee through the State Services portal, 30% discount is , which allows you to significantly save on the re-registration procedure.

How to install or replace license plate, parts and mounting locations

The rules allow the number plates to be installed in a frame, unless the registration plate is additionally covered with plexiglass. The frames are attached to the bumper with self-tapping screws and have several types of latches for fixing the plate with the number.

Each vehicle that is permitted to operate on the roads has an individual registration plate. The license plate is issued by the traffic police department and is a steel plate with embossed numbers and letters. The car owner is obliged to install it on the car in accordance with the rules. You can attach license plates to a new car with a frame yourself, after first checking the technical regulations.

How not to lose the state marks of a car when selling?

Until 2011, there was no legal way to retain the license plate from a deregistered vehicle. It was necessary to change the license plate each time the vehicle was re-registered. New registration certificate - new registration plates on the car, that was the general rule. However, in 2011 the order changed.

It has become possible, within the legal framework, to continue to use the state sign from the sold car on your new car. By the way, this is not so difficult to do. So, in short, the point is that an owner who is preparing to sell a car needs:

1. change the gas seals in advance to new ones;
2. hand over old registration plates that you don’t want to part with for safekeeping at the traffic police;
3. document all this;
4. when purchasing a new car, receive your surrendered plates where they were previously surrendered;
5. change the license plates on a new car and re-register it in your name - with new (i.e., your own old) license plates.

The right to preserve car license plates and the details of their preservation are regulated by clause 42 of the Order of the Ministry of Internal Affairs of the Russian Federation No. 399 of June 26, 2018 “On approval of the Rules for state registration of motor vehicles and trailers for them” and clause 58 of the Order of the Ministry of Internal Affairs of the Russian Federation “On approval of the Administrative Regulations of the Ministry of Internal Affairs of the Russian Federation on provision of public services for vehicle registration" dated August 7, 2013.

Legal requirements

According to Art. 12.2 of the Code of Administrative Offenses of the Russian Federation, driving a car without license plates is punishable by a fine of 500 rubles; a repeated violation threatens to deprive the driver of the right to drive a vehicle for up to 3 months. A similar punishment will follow for the fact that the sign is not installed in accordance with the regulations.

Removing license plates from a car

On American SUVs, the regular “registration” space does not meet the standard of Russian license plates. In this case, you can put the numbers in a frame on the car and fix it on the roof. It is important to remember that the distance from the ground to the top of the number panel should not exceed 2 meters.

When choosing a car with a non-standard bumper, drivers notice that the standard mounting points for the license plate do not match the holes in the license plate. Considering that the license plate must be clearly readable, without damaging the information part, the option of opening the frame for the license plate, installing it on the bumper and fixing it in accordance with the regulations remains the best.

Stages of installing and replacing a number

The rules allow the number plates to be installed in a frame, unless the registration plate is additionally covered with plexiglass. The frames are attached to the bumper with self-tapping screws and have several types of latches for fixing the plate with the number:

Only the owner can open the license plate on the car - all products have anti-vandal clips and fasteners.

Installation locations

Frames are installed in places specified by regulations. Metal frames are attached to the body with screws. To prevent corrosion at the points of contact between the screws and the metal, the screws and part of the bumper are treated with an anti-corrosion compound before installation. The best remedy, according to drivers' reviews, is a push-salon, into which the screw is dipped before screwing in.

To insert a car number into the frame, you will need a slotted screwdriver, which is convenient for moving the metal plate. For greater reliability, drivers attach the license plate to the panel with 2-3 self-tapping screws and only then use structural fasteners.

Place for mounting

In the book frame or Euro frame there is a folding panel that fixes the license plate around the perimeter. Polypropylene latches at the corners hold the panel securely. It is quite easy to remove the car number plate from the book frame, so additional screws are required.

The panel form has no moving parts. The design uses anti-vandal latches that hold the number. There is also additional fixation of the sign with two screws in the corners.

How to open/close number frame

While inserting a license plate into a frame on your car can take a few minutes, opening the panel can be difficult. The manufacturer uses anti-vandal latches, which break if opened incorrectly - it is impossible to steal the sign.

To open the panel in the book frame, you need to insert a thin screwdriver between the license plate and the panel strictly in the center of the folding part. Carefully unfasten the side “crocodiles” - the “book” will open.

Euro frames have small recesses on the side for a key with a plate. The original key is inserted into the slots and moves the internal lock. If you don't have a wrench at hand, you can use two slotted screwdrivers of the smallest size. They are inserted on both sides at the same time, they are also pressed at the same time - the side clamps move away, the number can be immediately removed.

Cost and where to buy

Almost all stores selling spare parts for cars have at least two or three types of license plate frames in their assortment.

However, if you need to buy a non-standard device or one equipped with any additional functions, it is better to contact specialized online stores.

Realdevice online store

It has been on the Russian market for more than 10 years.
It has a wide range of accessories for cars, including a considerable number of license plates. The store provides delivery of purchases throughout Russia. After completing the transaction, the goods will be transferred to the owner within 4 days. Illuminated products are the most popular on this portal. The average price ranges from 1,300 to 1,700 rubles.

Among customer reviews, positive ones dominate. They especially note the efficiency of the consultants’ work.

Online store GrantAuto.ru

The store was founded in 1997, the online project was launched in 2011.
All products offered have a manufacturer's warranty. In case of breakdown or defect, the product will be replaced with a quality one. The online portal has its own warehouses and stores, which makes it possible to refuse delivery and pick up the purchase yourself.

The store has a wide selection of license plate mounts with original inscriptions or additional functionality. The cost starts from 115 rubles.

Some clients note minor misunderstandings when communicating with the firm's consultants. Reviews about the quality of the product are positive.

Online store CyberKit

The store offers various mounts for license plates.
The cost varies from 120 to 1,500 rubles. The buyer can order home delivery or pick up the purchase from the warehouse themselves. The store regularly organizes promotions and discounts that reduce the price of goods. When ordering, employees call the buyer back and advise in detail on all the characteristics of the product.

How to set/remove a number

Number frames are manufactured according to standards, the size of the product exactly matches the size of the license plate (tolerance - plus 5 mm around the perimeter). Drivers have no difficulties with installation.

In this case, the frames turn out to be very convenient: the sign can be installed in 1 minute, secured with standard fasteners. And then, if necessary, screw it to the body with screws. To remove the license plate frame from the car, you only need a set of screwdrivers.

Fastening parts

The main fastening elements are galvanized screws for attaching the car number plate to the frame. Plastic fasteners remain additional fasteners, although they are considered quite durable and can withstand high mechanical pressure.

But since the screws provide end-to-end fixation of the metal plate and the metal number, the fastener is considered more reliable. Self-tapping screws are included, the standard length is up to 2 cm. They are screwed into the car body, bumper, trunk lid.

Source

How to remove and repair a license plate frame Homemade mounting frame

A 5,000 ruble fine or deprivation of the right to drive vehicles for a period of 1 to 3 months can be received upon meeting with a traffic inspector for the absence of at least one license plate on a car while driving on the roads or for deliberately hiding even one number or letter on the license plate. The same punishment can be received if license plates are installed incorrectly, for example, if even one of them “looks” at the asphalt.

Driving a car without traffic license plates is only allowed for newly purchased cars within 10 days from the date of purchase. But if the license plates are received before the expiration date, then you can drive the car without violating the rules only after attaching them to it. Therefore, before going to the State Traffic Safety Inspectorate for license plates, you should take care in advance of installing their mounting frames or another method of installing them on the car.

A 500 ruble fine or a warning can be received if it is impossible to see even one letter or number on a license plate from a distance of 20 meters due to natural contamination - dirt or snow getting on the license plate. If you are stopped by an inspector and there is a suspicion that the license plates of the car are dirty, then in order to get off with only a warning, you need to first wipe the license plates with a pre-prepared napkin before communicating with the inspector.

You should not agree with the inspector when he tries to equate the contamination of car license plates with their absence and the imposition of a fine of 5,000 rubles or deprivation of rights for up to three months. This is an illegal requirement. The maximum penalty under the law for such a violation can only be a fine of 500 rubles.

Therefore, in order to avoid imposition of a fine or deprivation of driving privileges, it is necessary to correctly and securely attach the license plate and promptly clean its surface from dirt.

Types of number frames

If we talk about what an illuminated license plate frame is, then everything is simple. In fact, every car has a “native” license plate light, but most often it shines dimly and somewhere in the depths of the car. Illuminated frames illuminate the entire perimeter of your license plate, making your registration number clearly visible at any time of the day.

Well, for those who prefer to first of all make sure that the numbers are not removed, there are special anti-vandal frames.

Anti-vandal frames

Such accessories are simple but quite effective elements for protecting rooms from thieves. Thanks to a special fastening technology, an attacker, even with all his diligence, will not be able to remove such a sign. It is impossible to unscrew the secret screws, since they are intended only for a single installation, so they cannot be unscrewed with a regular screwdriver.

Curtain frames

Among drivers, there are increasingly those who prefer the frame to perform slightly “other” functions, namely to help hide from the eyes of traffic police representatives and traffic cameras. The benefit here is questionable, since it is one thing to pay for a slight speeding, and another thing to lose your license and a considerable sum of money for using an illegal device. But as they say, “there is no need for invention,” and today a car enthusiast can easily buy a frame equipped with a special curtain.

Externally, the curtain frame for the license plate looks like a regular one, but when you press just one button, a black opaque curtain falls down, protecting the registration number. The radio remote control for this frame can be carried with you or left in the car. In this case, you can close both numbers at once, or only one of them. For the convenience of motorists, so that they do not forget to open the curtain in a timely manner, a special light indicator is provided. Such accessories cost from 3,500 rubles.

This is interesting: How to make a car fragrance with your own hands

In addition to protecting you from vandals, dirt and dust, such an element will make you invisible to traffic cameras. Among the “tricky” frames, there are also other options.

Flip frames

For those who have acquired two registration numbers, there are reversible frames that allow, if necessary, to rotate one sign 180 degrees, replacing it with another alphanumeric number. It's impossible to remove numbers from this frame, so you don't have to use it if you're a Carrier fan. You can install any picture in place of one of the signs and display it overnight to prevent any attempts at vandalism.

Slanted frames

Thanks to the angle of inclination, your number will simply not be visible to cameras. Such devices differ in their operating principle and are:

• Electronic folding. After pressing a special button, the number “reclines” to a horizontal position.
• Self-reclining. Such elements recline depending on the speed of the oncoming air, respectively, if you are moving at normal speed, the sign remains in the field of view, but as soon as the speed has been increased, the frame begins to bend.

Such products cost about 7,000 rubles, but the price may vary, since they are not manufactured by official dealership auto centers.

At the same time, according to the majority of those who like to “drive”, there are no contradictions in the direction of the legislation of the Russian Federation in this case, because the license plate is there, it is visible, and the fact that it is located at the “wrong” angle is no longer a problem for the motorist. Well, judge for yourself here, because no one has yet repealed Article 12.2 Part 2 of the Code of Administrative Offenses of the Russian Federation, which clearly states that when driving a vehicle with a state registration plate, equipped with the use of materials that prevent or complicate the identification of the car, the fine can amount to at 5,000 rubles. In some cases, a penalty in the form of deprivation of rights for up to 3 months may follow. The same applies to any other framework in which a mechanism is provided that prevents the real registration number of the car from being determined. That is, if you use an inverted, tilted or curtain frame, then you risk getting a fine.

License plate frame with rear view camera

Today there are frames on sale equipped with a rear view camera. Such devices are very convenient when parking and are an improved analogue of parking sensors. The latter are not equipped with a rear view camera, so if there is a snag or a high curb on the way, you risk damaging the car. If the car is equipped with a license plate with a rear view camera, then the driver will see everything that is happening behind the car.

This is interesting: Which car alarm can be considered the best?

Moreover, the cameras in such frames are rotating, so you can see not only what is directly in front of the peephole, but also the overall picture. Such products cost from 2,500 rubles.

If we talk about the material from which the frame for the state can be made. numbers, then today there are both metal and plastic elements.

Do-it-yourself plastic license plate holder repair

The license plate holder has been removed from the car, and now you can repair it yourself in a workshop.

As you can see in the photo, the cracked part of the frame is several millimeters thick. Therefore, it can be repaired by combining two technological methods - gluing and reinforcement with metal brackets.

Gluing the cracked part of the frame will not provide high reliability, and is only necessary for the convenience of installing brackets. In order not to wait long, gluing was done using Super Moment quick-setting adhesive.

Next, using an electric soldering iron, the joint was reinforced with two brackets made of copper wire for electrical wiring with a diameter of about 1 mm.

The brackets were recessed into the plastic flush with the surface of the frame and became almost invisible. For clarity, the photograph shows brackets that have not yet been melted over with plastic. Repair using thermal reinforcement of brackets in plastic provides a complete guarantee that the connection will never come apart.

To repair the plastic loop located on the top of the license plate holder, we had to use a slightly different technology.

Before the repair, the movable part of the license plate holder was fixed in its base and the crack was repaired using an electric soldering iron.

But reflow repairs cannot ensure a reliable connection, so an additional specially shaped bracket was bent from a paper clip, as shown in the photograph.

Next, the bracket was fused using a soldering iron into the number holder, as shown in the photo. The fused metal bracket will ensure high reliability of the connection.

The bracket was recessed into the body of the plastic, and all that remained was to level the surface with sandpaper. Despite the rigidity of the connection, the lower part of the frame tilted freely a couple of centimeters, which is quite enough to tuck a license plate into the license plate holder.

But the unexpected happened. The frost outside was more than 25°C, and after attaching the license plate holder to the car's bumper, it was impossible to attach the license plate to the holder. The plastic lost its elasticity from the cold, and the latches did not want to lock. I had to use plastic clamps again.

How to remove a plastic license plate holder from a car

One frosty winter morning, while clearing snow from the car, I discovered that the plastic holder for the front license plate of the car, which had served faithfully for more than seven years, had a cracked frame, and several lower fasteners had come out of the grooves. The license plate at one of the lower corners protruded from the frame at the bottom and was held on “on my word of honor.” I was lucky that I discovered the breakdown in time, since on one of the potholes while the car was moving, the number plate would have definitely fallen out of the holder.

In severe frost, the plastic of the holder lost its elasticity, and an attempt to secure the frame at its base using standard clamps was unsuccessful. There was no time to carry out repairs and the license plate had to be temporarily secured using two plastic clamps threaded through the holes provided for fastening in it and the frame. The reliability of fastening with clamps was in doubt, so at the first opportunity I started repairing the license plate holder.

The license plate is secured in the holder using a movable frame. Its upper part at the base is held by elastic plastic loops, which makes it possible to move the lower part of the frame slightly to the side when installing the number at the base of the holder. The photo shows the loop that broke in my number holder.

After installing the number in the base of the holder, the lower part of the frame in its base is secured using several latches shown in the photo. In order to remove the license plate from the holder, these latches must be disengaged one by one using a flat-head screwdriver.

After removing the license plate, access to the screws securing the license plate holder opens. As you can see in the photo, the holder on the car bumper is secured with two screws.

In order to remove the plastic holder from the car bumper, simply unscrew the self-tapping screws using a Phillips screwdriver.

Making a metal car license plate holder with your own hands

Since it was not possible to secure the license plate in the plastic license plate holder after it was repaired in the cold, I had to make a new license plate holder with my own hands from scrap material.

There was a suitable sized aluminum plate with a thickness of 2 mm available, and it was decided to make a homemade license plate holder from it. Aluminum is lightweight, durable, easy to process and does not oxidize when exposed to precipitation. Dimensions were taken from the license plate and the drawing presented above was made.

The size of 150 mm was chosen based on the holes in the car bumper made earlier to secure the plastic license plate.

The number holder was cut from a sheet using a hacksaw, the corners were rounded with a flat file with a coarse notch. The holes are drilled using a drill with a metal drill. All that remains is to install the homemade license plate holder on the car bumper and secure the license plate to it with screws.

When attaching the license plate holder to the bumper, a difficulty arose with the screws. Since the license plate must fit tightly to the plane of the license plate, we needed plastic self-tapping screws with a countersunk head, a large thread pitch and so that the threads start at the head itself. Finding such a screw turned out to be problematic, but I remembered that in the computer power supply the cooler in its case is screwed with just such self-tapping screws with a diameter of 4 mm. I unscrewed the screws from the burnt out power supply.

A self-made license plate holder was screwed to the car bumper with self-tapping screws. For more reliable fastening, you can use screws with metric threads, threaded through the bumper, and screwed into nuts with wide washers located on the inside of it.

Although, according to the Requirements for installing state registration plates on vehicles, bolts or screws with heads that have the color of the sign field or light galvanic coatings must be used to secure them, I did not have any screws with beautiful heads on hand that meet these requirements. Therefore, I used it with a dark coating, since the diameter of their heads is only 3 mm larger than the holes in the license plate and at a glance it is practically not noticeable. In any case, the State Traffic Safety Inspectorate employees do not ask questions.

The screws used were M6 with a thread length of 10 mm, with a spherical head for a hex bit. To prevent spontaneous unscrewing of the threaded connection, a spring washer of the “grower” type was installed between the nut and a simple washer.

Now the license plate on the car is secure and looks elegant. I plan to replace the plastic holder for the mount and rear license plate with a homemade one in the near future.

Source

Choosing a mounting location

Many modern vehicle models have a space specifically designed for attaching a license plate. Then the error is practically eliminated, and it is clear how to attach the license plates to the car.

In the absence of such a hint, it will be much more difficult to navigate. But don’t rush and make mistakes. To carry out such work correctly, it is recommended to study the special GOST on state registration plates for a vehicle, their types and main dimensions, and technical requirements.

Among the main requirements in this document are:

1. It is prohibited to install a front or rear license plate that deviates to the right from the axis.
2. Installation is carried out exclusively on a flat, vertical, rectangular surface.
3. Elements included in the design of the vehicle must not obscure the number.
4. The choice of mounting location is carried out so that the license plate is not subject to contamination and can always be successfully identified.
5. The license plate plate must not reduce the vehicle's overhang and extend beyond its dimensions.
6. When installing, it is important not to cover parts of external light and signaling devices.
7. To install a license plate on the surface of a bumper of non-standard sizes, it is practiced to perform such actions at an angle. This is prohibited by law and is fraught with corresponding punishment.